Program Mode and the Program Editor
Using the Program Editor
6-8
Fine Adjust
You can add slight detuning to the pitch by changing the Þne adjust parameter. Notice that
there are actually two Þne adjust parameters on the PITCH page: one that changes the pitch in
cents (100ths of a semitone), and one that changes it according to its frequency (in increments of
HertzÑcycles per second). Since weÕre discussing the universal control sources here, and not
speciÞcally pitch, weÕll move on for now, as the ÒFine HzÓ parameter applies only to pitch-
related functions. See ÒThe PITCH Page,Ó later in this chapter, which describes Fine Hz more
thoroughly.
Key Tracking
This is a quick way to get additional control based on the MIDI note number of each note you
trigger. Key tracking applies a different control signal value for each note number. In the case of
pitch, key tracking enables you to change the tuning of each note relative to its normal pitch.
Middle C is the zero point. Regardless of the key tracking value, there is no effect on Middle C.
If you set a non-zero value for key tracking, the effect increases for each note above or below
Middle C. In the case of pitch, for example, say you assign a value of 5 cents per key for the key
tracking parameter. Triggering Middle C (C 4 on the K2vx) will play a normal C 4. Triggering
C# 4 will play a note 5 cents higher than C# 4. Triggering D 4 will play a note 10 cents higher
than D 4, and so on. Notes below Middle C will be tuned lower than their normal pitches. If
you set a negative value for key tracking, notes above Middle C will be tuned lower than their
normal pitches.
Keep in mind that key tracking on the PITCH page works in conjunction with the key tracking
parameter on the KEYMAP page. This is why you can set the KeyTrk parameter on the PITCH
page to 0ct/key, and the K2vx will still increases in pitch by 100 cents/key as you go up the
keyboard. ItÕs because the KeyTrk parameter on the KEYMAP page is already set at 100 cents/
key.
Velocity Tracking
A positive value for velocity tracking will raise the pitch as you trigger notes with higher attack
velocities. This is great for getting a trace of detuning based on your attack velocity, especially
in drum programs, where you can make the pitch of the drum samples rise slightly with
higher-velocity Note Ons, just as drums do when you strike them harder. Negative values will
lower the pitch as you increase the attack velocity.
Source 1
This parameter takes its value from a long list of control sources (you can Þnd it in the
Reference
Guide
ÑitÕs called the Control Source list) including every MIDI control number, a host of LFOs,
ASRs, envelopes and other programmable sources.
Src1 works in tandem with the parameter beneath it on the page: Depth. Choose a control
source from the list for Src1, then set a value for Depth. When the control source assigned to
Src1 is at its maximum, the pitch will be altered to the full depth you set. For example, if you set
Src1 to ÒMWheel,Ó and set Depth to 1200 ct, the pitch will rise as you push the Mod Wheel up
on your MIDI controller, reaching a maximum of 1200 ct (12 semitones, or one octave).
Source 2
This oneÕs even cooler. Like Src1, you choose a control source from the list. But instead of
setting a Þxed depth, you can set a minimum and maximum depth, then assign another control
source to determine how much depth you get. Try this example. (Make sure Src1 is set to OFF
Þrst, so the two sources donÕt interact). Start with Program 199, and press EDIT. Press the
PITCH soft button to select the PITCH page. Set the Src2 parameter to a value of LFO1, then set
the Minimum Depth parameter to 100 ct, and Maximum Depth to 1200 ct. Then set the Depth
Содержание K2500RS
