KUHN Venta 3030 Скачать руководство пользователя страница 81

Страница: 81 / 136

9. - Instructions for work

Venta 3030-3530-4030

RN034AGB D

Seed Drill

Adjustment procedure:

Blower driven by tractor hydraulics

- Start up the tractor hydraulics.
- Run the engine at approximately 1500 min

-1

- Gradually increase the tractor valve oil flow rate

until you reach a nominal blower rotational speed
of 4250 min

-1

Blower with independent control equipped with a

regulator (Vario system)

- The flow control valve is factory preset at 7.
- Switch the control terminal on.
-

Check the blower speed on the

CCI 1200/VT 50/QUANTRON S-2 control
terminal.

- Engage the tractor PTO and increase speed

gradually until a speed of 1000 min-1 is reached.

- Adjust the blower speed using the hand wheel 1.

• Turn the hand wheel clockwise: the blower speed is

increased.

- Switch the control terminal on.

• Blower rotational speed is on display.

- Reduce the oil flow rate from the tractor valve to a

minimum.

- Turn wheel (1) to the maximum.

The regulation valve limits the blower unit
maximum rotational speed to prevent
damage to the blower.

Содержание Venta 3030









































































































































Результаты поиска

Содержание Venta 3030

Отзывы:

Похожие инструкции для Venta 3030

Бренды по названию

Популярные бренды

KUHN Venta 3030, Руководство оператора

Результаты поиска

Содержание Venta 3030

Отзывы:

Похожие инструкции для Venta 3030

Бренды по названию

Популярные бренды