KUHN Venta 3030 Скачать руководство пользователя страница 17

Страница: 17 / 136

4. - Safety

Venta 3030-3530-4030

RN034AGB D

Seed Drill

4.2.6 Precautions when driving on public

roads



Dimensions

Depending on the dimensions of the machine,
contact the relevant authorities to ensure that it can
be legally transported on public roads.

If the machine is over the maximum legal size,
follow the local regulations for special transportation
of oversize equipment.



Transport position

Before transporting the machine on public roads,
place the machine into its transport position,
according to the instructions in this manual.



Lights and indicators

Before transporting the machine on public roads,
ensure that all legally required lightings and
signallings are in place.

Ensure that lightings and signallings are clean and in
good working order. Replace any missing or broken
equipment.

Always obey current regulations for driving
on roads.

Содержание Venta 3030









































































































































Результаты поиска

Содержание Venta 3030

Отзывы:

Похожие инструкции для Venta 3030

Бренды по названию

Популярные бренды

KUHN Venta 3030, Руководство оператора

Результаты поиска

Содержание Venta 3030

Отзывы:

Похожие инструкции для Venta 3030

Бренды по названию

Популярные бренды