KUHN Venta 3030 Скачать руководство пользователя страница 73

Страница: 73 / 136

9. - Instructions for work

Venta 3030-3530-4030

RN034AGB D

Seed Drill

9.3

Adjustments in working position

Before:

Position the power harrow horizontally with

respect to the ground.

- Adjust the impulse wheel depth.



Hydraulic top link

- Completely remove the third hydraulic point from

the machine.

- Position the hopper using the hydraulic top link set

in the most horizontal position with regards to the
ground.

- Loosen counter nut (1).
- Turn rod (2) until the hopper is horizontal with

regards to the ground.

- Tighten checknut (1).



Mechanical top link

- Loosen nut (1).
- Rotate the mechanical top link and adjust length so

that the hopper is horizontal with regards to the
ground.

- Tighten nut (1).

Содержание Venta 3030









































































































































Результаты поиска

Содержание Venta 3030

Отзывы:

Похожие инструкции для Venta 3030

Бренды по названию

Популярные бренды

KUHN Venta 3030, Руководство оператора

Результаты поиска

Содержание Venta 3030

Отзывы:

Похожие инструкции для Venta 3030

Бренды по названию

Популярные бренды