KUHN GMD350 Скачать руководство пользователя страница 88

Страница: 88 / 100

Disc mower

GMD350 - 350-FF

Trouble shooting guide

Too frequent safety breakback

release.

Insufficient spring washer

compression.

Increase spring washer

compression.

When the following equipment

is fitted:

Mechanical safety r

Hydraulic pivot

Interference between tractor

and front guard.

Incorrect cam adjustment.

Adjust machine pivot moment.

Incorrect mowing unit

positioning with regards to the
tractor when placed in working
position.

The tractor valve double acting

position has not been used to
lower the mowing unit.

Use the tractor double acting

position to lower the mowing
unit.

When the following equipment

is fitted:

Mechanical safety r

Hydraulic pivot

If the cutter bar pivots

rearwards during the first
headland turn manoeuvre.

The valve actuator is still

engaged in the cam.

Lower the chassis prior to

raising it for positioning the
hitch pins at 450 mm (1’5’’)
from the ground.

Adjust the cam position.

See section:

- ’’Adjusting the pivot

sequence of the machine’’.

Содержание GMD350





































































































Результаты поиска

Содержание GMD350

Отзывы:

KUHN GMD350, Руководство оператора, Страница: 88 / 100

Результаты поиска

Содержание GMD350

Отзывы: