KUHN GMD350 Скачать руководство пользователя страница 50

Страница: 50 / 100

Disc mower

GMD350 - 350-FF

Instructions for work

2. Adjustments in working position

Cutting height

The desired cutting height is obtained directly by

adjusting the top link length. The height can be adjusted
from 30 to 60 mm (1.1" - 2.4").

To obtain a different cutting height:

- Place the machine in working position.
- Lift the machine chassis using the tractor lift.

- Shut-off the mowing unit ground pressure circuit valve

(1) using 18mm box spanner.

- Lower the tractor lift linkage in working position:

• The distance between hitch pin axis and the ground

must be of 450 mm (1’5’’).

- Modify the top link length to alter the machine tilt

angle.

- Check cutting height.

Before leaving the tractor or before
adjusting, maintaining or repairing the
machine, disengage the PTO drive, turn off
the engine, remove ignition key and wait until
all moving parts have come to a complete
stop and apply park brake.

Ground pressure circuit valve:

- Valve open (a)
- Valve closed (b)

The following procedure puts the machine
mechanism under tension and balances
plays in the tractor-mechanism coupling
links.

- Never open the ground pressure circuit

valve prior to having coupled the
machine to the tractor lower links and
top link.

Содержание GMD350





































































































Результаты поиска

Содержание GMD350

Отзывы:

KUHN GMD350, Руководство оператора, Страница: 50 / 100

Результаты поиска

Содержание GMD350

Отзывы: