KUHN GMD350 Скачать руководство пользователя страница 33

Страница: 33 / 100

Putting into service

Disc mower

GMD350 - 350-FF

If measure A is comprised between 2.10 m (6’11")

and 2.25 m (7’04"):

- Place lower links in position b:

Adjust machine lower hitch pin position:

- Loosen the 8 screws (3).
- Centre hitch pin (1) with regards to the mounting plate.
- Tighten 4 hitch pin screws (1).

• Torque : 12 daN m (89 lbf ft).

- Position hitch pin (2) at measure (X = 825 mm (2’8").
- Tighten 4 hitch pin screws (2).

• Torque : 12 daN m (89 lbf ft).

If measure A is comprised between 2.25 m (7’04")

and 2.40 m (7’10"):

- Place lower links in position c:

Adjust machine lower hitch pin position:

- Loosen the 8 screws (3).
- Position hitch pin (2) at measure G = 10 mm (0.4").
- Tighten 4 hitch pin screws (2).

• Torque : 12 daN m (89 lbf ft).

- Position hitch pin (1) at measure (X = 825 mm (2’8").
- Tighten 4 hitch pin screws (1).

Torque : 12 daN m (89 lbf ft).

Содержание GMD350





































































































Результаты поиска

Содержание GMD350

Отзывы:

KUHN GMD350, Руководство оператора, Страница: 33 / 100

Результаты поиска

Содержание GMD350

Отзывы: