KUHN GMD350 Скачать руководство пользователя страница 52

Страница: 52 / 100

Disc mower

GMD350 - 350-FF

Instructions for work

To check the ground pressure::

- Place the machine in working position.
- Lower tractor lift linkage until obtaining a distance of

450 mm (1’5’’) between the hitch pin pivot point and
the ground.

- Check the pressure given on the gauge:

The pressure must be adapted to the nature and

moisture degree of the ground.

Pressure adjustment

Increase the hydro-pneumatic accumulator pressure to

reduce the mowing unit ground pressure:

- Place the machine in working position.
- Open valve (1) of hydraulic valve bank using 18mm

box spanner supplied with the machine.

- Use mowing unit lift cylinder to lift the mowing unit.
- Check the pressure increase indication on the gauge.
- When the required pressure is reached, close the

valve.

Conventional pressure = 105 bar (psi).

MINIMUM operating pressure = 95 bar (psi).

MAXIMUM operating pressure = 115 bar (psi).

Never adjust machine to a pressure not
comprized between these limit values.

Hydraulic valve:

- Valve open (a) (Adjustment)
- Valve closed (b) (Work and transport)

Содержание GMD350





































































































Результаты поиска

Содержание GMD350

Отзывы:

KUHN GMD350, Руководство оператора, Страница: 52 / 100

Результаты поиска

Содержание GMD350

Отзывы: