KUHN GMD350 Скачать руководство пользователя страница 69

Maintenance and storage

Disc mower

GMD350 - 350-FF

67

„

Hydro-pneumatic accumulator

The hydro-pneumatic accumulator does not require any

particular maintenance.

Regularly check the tightness of the accumulator

attachment on the hydraulic valve bank and that no oil
has leaked from the hydraulic circuit (a small oil leak can
change settings).

Depressurize the hydraulic circuit

Suspension hydraulic circuit:

- Stop the tractor engine.

- Shift the mowing unit lift cylinder directional control

valve in float position.

- Open valve (position (a)).

- Release pressure until the gauge needle reads 0.
- When the pressure reaches 0 bar (0 psi) bar on the

pressure gauge, close the valve (position b.

Pressurizing the hydraulic circuit

See section:

- ’’Pressurizing the hydraulic ground pressure circuit’’.

Before any work is carried out on a hydraulic
circuit with hydro-pneumatic accumulator,
depressurize the circuit.

It is strictly forbidden to weld, grind or drill
onto a hydro-pneumatic accumulator. 

Hydraulic valve:

- Valve open (a) (Adjustment)
- Valve closed (b) (Work and transport)

Содержание GMD350





































































































Отзывы: