KUHN GMD350 Скачать руководство пользователя страница 70

Страница: 70 / 100

Disc mower

GMD350 - 350-FF

Maintenance and storage

Cutterbar

Draining

From the working position:

- Remove filler plug (1) and its seal.

The cutter bar is lubricated for life and does not require regular maintenance.

If in doubt as to the oil quantity contained in the cutterbar, fully drain and refill cutterbar
respecting recommended oil quantity and quality.

Following all service operations or in case of an oil leak, empty an refill cutterbar.

Before draining oil, operate the machine for a
few minutes so that the oil warms up..

The cutterbar is lubricated with 4.5 L (1.18 US gal) of SPIRAX A extreme-pressure gear oil with viscosity
grade ASX 75W90 and API grade GL5 .

Never use an oil of viscosity SAE 90 in the
cutterbar.

When optional equipment is used, follow
specific procedures mentioned in the related
section:

- Chain stroke limiter.

Содержание GMD350





































































































Результаты поиска

Содержание GMD350

Отзывы:

KUHN GMD350, Руководство оператора, Страница: 70 / 100

Результаты поиска

Содержание GMD350

Отзывы: