KUHN GMD350 Скачать руководство пользователя страница 34

Страница: 34 / 100

Disc mower

GMD350 - 350-FF

Putting into service

Pressurizing the hydraulic ground pressure
circuit

The optimal suspension is obtained with the mowing unit

ground pressure set to the minimum, in such a way that
the unit does not lift off the ground when going over
irregular ground contours.

- Couple the machine to the tractor

• ( See section: Coupling the machine ).

- Lower tractor lift linkage until obtaining a distance of

450 mm (1’5’’) between the hitch pin pivot point and
the ground.

- Open valves (1) using 18 mm box spanner:

• (a) Hydraulic valve bank.
• (b) Ground pressure circuit.

- Activate the transport/work cylinder control valve in

the "pivot into transport" position.

- Check the pressure increase indication on the gauge.
- Shut-off valve of the hydraulic valve bank when the

pressure reaches 105 bar (1523 psi) on the gauge

The machine hydraulic ground pressure
circuit is factory set without pressure.

Conventional pressure = 105 bar (1523 psi)

Hydraulic valve:

- Valve open (a)
- Valve closed (b)

Ground pressure circuit valve:

- Valve open (a)
- Valve closed (b)

Содержание GMD350





































































































Результаты поиска

Содержание GMD350

Отзывы:

KUHN GMD350, Руководство оператора, Страница: 34 / 100

Результаты поиска

Содержание GMD350

Отзывы: