KUHN GMD350 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 100

KUHN GMD350 Скачать руководство пользователя страница 17

Safety

Disc mower

GMD350 - 350-FF

15

Precautions during manoeuvres

When moving the machine from the transport position to

the working position and vice versa, make sure that
nobody is within the machine pivoting area.

Remote controlled components

Danger of crushing and shearing can exist when

components are operated by hydraulic or pneumatic
controls. Keep away from these danger zones.

Safety decals

Safety warning decals are placed in pictorial form on

various parts of the machine. They are there to warn you
of potential dangers and to tell you how to avoid
accidents.

Always keep the safety decals clean and readable, and

replace them when they are worn, damaged, missing or
illegible.

Waste disposal

Respect the environment! Never spill pollutants (oil,

grease, filters, etc.) on the ground, never pour them
down the drain and never discard them in any other
place where they could pollute the environment. Never
throw away or burn a tyre. Always take waste to
specialized recycling or waste disposal centers.

«
...
15
16
17
18
19
...
»

Содержание GMD350





































































































Отзывы:

Нет отзывов