TRANSAXLE
G23, G26, WSM
2-S8
(EU)
Adjustment of HST Neutral Position
1. Start the engine.
2. Keep the engine at the maximum revolution.
3. Loosen the locking screw (2).
NOTE
• When adjusting the HST neutral position, loosen the
locking screw approximately 2 turns counterclockwise not
to drop the nut inside.
(Forward to Neutral Position)
4. Depress the speed control pedal (1) to
"Forward"
speed
position, and release the foot from the speed control pedal (1).
Check that the rear axle (or the wheel) stops rotating.
If the rear axle (or the wheel) does not stop rotating, move the
position of the locking screw (2) to the machine front side to stop
rotating.
(Reverse to Neutral Position)
5. Depress the speed control pedal (1) to
"Reverse"
speed
position, and release the foot from the speed control pedal (1).
Check the rear axle (or the wheel) stops rotating.
If the rear axle (or the wheel) does not stop rotating, adjust the
locking screw (2) to stop rotating.
6. After adjusting the neutral position, tighten the lock screw (2)
securely.
9Y1210294TXS0006US0
Charge Relief Pressure
CAUTION
• When checking, park the machine on flat ground.
1. Lift up the rear wheels by supporting the machine frame.
2. Remove the plug (G 1/4) (2) or (4) from the HST centre section,
then install the adaptor (G 1/4) and pressure gauge.
3. Start the engine and run it at the maximum speed.
4. Read the pressure gauge to measure the charge relief
pressure.
5. If the measurement is not within the factory specifications,
check the charge relief valve and related hydraulic components.
NOTE
• When reinstalling the hexagon socket head plug, apply
liquid lock (Three Bond 1324 or its equivalent) to the plug.
9Y1210294TXS0007US0
(1) Speed Control Pedal
(2) Locking Screw
(3) HST Neutral Plate
A : Reverse
B : Forward
Charge relief pressure
Factory specification
(Oil temperature at
50 °C, 122 °F)
0.4 to 0.6 MPa
4.1 to 6.1 kgf/cm
2
60 to 80 psi
Tightening torque
Charge relief pressure port
plug (G 1/4)
29 to 44 N·m
3.0 to 4.5 kgf·m
22 to 32 lbf·ft
(1) Brake Lever
(2) Plug (G 1/4) (Reverse)
(3) By-pass Valve
(4) Plug (G 1/4) (Forward)
KiSC issued 08, 2009 A
Содержание G23
