manualshive.com logo in svg

Kubota G23, Руководство по ремонту

Поделиться
Скачать
Kubota G23 Скачать руководство пользователя страница 215

FRONT AXLE

G23, G26, WSM

3-S9

(EU)

[3] SERVICING

Clearance between Centre Pin and Bushing

1. Measure the centre pin O.D. with an outside micrometer.
2. Measure the bushing I.D. of the front axle with a cylinder gauge.
3. If the clearance exceeds the allowable limit, replace it.

9Y1210294FAS0010US0

Clearance between 
centre pin and pin 
support bushing

Factory specification

0 to 0.231 mm
0 to 0.00909 in.

Allowable limit

0.70 mm
0.0276 in.

Centre pin O.D.

Factory specification

19.850 to 20.000 mm
0.78149 to 0.78740 in.

bushing I.D.

Factory specification

20.000 to 20.081 mm
0.78740 to 0.79059 in.

(1) Front Axle
(2) Bushing
(3) Centre Pin

L : Front Axle Centre Bush I.D.
M : Place to measure centre pin O.D.

KiSC issued 08, 2009 A

Содержание G23
























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды