Kubota G23 Скачать руководство пользователя страница 292

Страница: 292 / 343

ELECTRICAL SYSTEM

G23, G26, WSM

6-S14

(EU)

(7) Grass Collector Duct Switch

Grass Collector Duct Switch Continuity

1. Remove the grass collector duct switch from the machine.
2. Measure the resistance with an ohmmeter across the switch

terminals (1), (4).

3. If the resistance values specified below are not indicated, the

grass collector duct switch is faulty.

Switch lever is free (released)

Switch lever is pushed

9Y1210294ELS0013US0

(8) Grass Collector Buzzer

Buzzer Function Check

1. Remove the grass collector buzzer from the machine.
2. Connect a jumper lead between the battery positive terminal

and the terminal

(2).

3. Connect a jumper lead between the battery negative terminal

and the terminal

(1).

4. Check the buzzer function.
5. If the buzzer noise level is low, change the buzzer with a new

one.

(Reference)

9Y1210294ELS0014US0

(9) Fuel Pump

Connector Voltage

1. Disconnect the

connector from the fuel pump.

2. Turn the main switch key to the

"ON"

position, and measure the

voltage with a voltmeter between the connector terminals.

3. If the voltage differs from the battery voltage, the wiring harness

or main switch is faulty.

9Y1210294ELS0015US0

Resistance

Terminal 1

- Terminal

Factory specification

Ω

Resistance
Terminal

- Terminal

Factory specification

Infinity

(1) Terminal

(2) Lead (COM)
(3) Switch Lever

(4) Terminal

(5) Lead (NC)

Buzzer noise level

75 to 95 dB / 1m (A), 39.87 in. (A)

(1) Terminal

(Black)

(2) Terminal

(Red)

(3) Lead (Red)

(4) Buzzer Body
(5) Lead (Black)

Voltage

Between connector
terminals

Approx. battery voltage

KiSC issued 08, 2009 A

Содержание G23
























































































































































































































































































































































Результаты поиска

Содержание G23

Отзывы:

Бренды по названию

Популярные бренды

Kubota G23, Руководство по ремонту

Результаты поиска

Содержание G23

Отзывы:

Бренды по названию

Популярные бренды