manualshive.com logo in svg

Kubota G23, Руководство по ремонту

Поделиться
Скачать
Kubota G23 Скачать руководство пользователя страница 226

STEERING

G23, G26, WSM

4-S4

(EU)

4. CHECKING DISASSEMBLING AND SERVICING

[1] CHECKING

(1) Power Steering Relief Valve

Relief Valve Operating Pressure

1. Disconnect the power steering delivery hose L (or R) from

steering controller, and set pressure gauge and hose.

(Reference)

• Hose and adaptor size : 9/16-18UNF, 37 ° flare

1. Start the engine and set at maximum speed.
2. Fully turn the steering wheel to the left (or right) to check the

feeling which the steering wheel lightly locks. Read the relief
valve operating pressure when the steering wheel to the above
mentioned lock position by operation force at approximately 9.8
N (1.0 kgf, 2.2 lbf) of outer.

NOTE

• After set a pressure gauge, be sure to bleed air.
• Note that the pressure valve changes by the pump action of

the power steering controller when the steering operation
is continued after the steering wheel is lightly locked and
accurate relief valve pressure cannot be measured.

• After checking relief valve operating pressure, bleed the air

in the power steering hydraulic circuit.

9Y1210294STS0005US0

Relief valve operating 
pressure

Factory specification

8.34 to 8.82 MPa
85.0 to 90.0 kgf/cm

2

1210 to 1270 psi

(1) Power Steering Delivery Hose
(2) Power Steering Controller

(3) Pressure Gauge Hose
(4) T Type Adaptor

KiSC issued 08, 2009 A

Содержание G23
























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды