Kubota G23 Скачать руководство пользователя страница 101

Страница: 101 / 343

ENGINE

G23, G26, WSM

1-S19

(EU)

Radiator Water Leakage

1. Pour a specified amount of water into the radiator.
2. Set a radiator tester (1) and an adaptor (2) and raise the water

pressure to the specified pressure.

3. Check the radiator for water leaks.
4. For water leak from the pinhole, repair with the radiator cement.

When water leak is excessive, replace the radiator.

NOTE

• The pressure of the leak test is different from each radiator

specification.
Thus, do the leak test, refer to the test pressure of each
radiator specification.

9Y1210294ENS0010US0

Thermostat Valve Opening Temperature

1. Suspend the thermostat in the water by a string with its end

inserted between the valve and seat.

2. Heating the water gradually, read the temperature when the

valve opens and leaves the string.

3. Continue heating and read the temperature when the valve

opens approx. 8 mm (0.3 in.).

4. If the measurement is not within the factory specifications,

replace the thermostat.

9Y1210294ENS0012US0

Radiator water leakage
test pressure

Factory specification

No leak at specified
pressure

(1) Radiator Tester

(2) Adaptor

Thermostat's valve
opening temperature

Factory specification

69.5 to 72.5 °C
157.1 to 162.5 °F

Temperature at which
thermostat completely
opens

Factory specification

85 °C
185 °F

KiSC issued 08, 2009 A

Содержание G23
























































































































































































































































































































































Результаты поиска

Содержание G23

Отзывы:

Бренды по названию

Популярные бренды

Kubota G23, Руководство по ремонту

Результаты поиска

Содержание G23

Отзывы:

Бренды по названию

Популярные бренды