Kubota G23 Скачать руководство пользователя страница 115

Страница: 115 / 343

ENGINE

G23, G26, WSM

1-S33

(EU)

Tappets

1. Remove the tappets (1) from the crankcase.

(When reassembling)

• Visually check the contact between tappets and cams for proper

rotation. If defect is found, replace tappets.

• Before installing the tappets, apply engine oil thinly around

them.

IMPORTANT

• Do not change the combination of tappet and tappet guide.

9Y1210294ENS0036US0

Valves

1. Remove the valve caps (2).
2. Remove the valve spring collet (3), pushing the valve spring

retainer (4) by valve spring replacer (1).

3. Remove the valve spring retainer (4), valve spring (5) and valve

stem seal (6).

4. Remove the valve (7).

(When reassembling)

• Wash the valve stem and valve guide hole, and apply engine oil

sufficiently.

• After installing the valve spring collets, lightly tap the stem to

assure proper fit with a plastic hammer.

IMPORTANT

• Do not change the combination of valve and valve guide.

9Y1210294ENS0037US0

Thermostat Assembly

1. Remove the thermostat cover mounting screws (1), and remove

the thermostat cover (2).

2. Remove the thermostat assembly (4).

(When reassembling)

• Apply a liquid gasket (Three Bond 1215 or equivalent) only at

the thermostat cover side of the gasket (3).

9Y1210294ENS0029US0

(1) Tappet

(1) Valve Spring Replacer
(2) Valve Cap
(3) Valve Spring Collet
(4) Valve Spring Retainer

(5) Valve Spring
(6) Valve Stem Seal
(7) Valve

(1) Thermostat Cover Mounting Screw
(2) Thermostat Cover

(3) Thermostat Cover Gasket
(4) Thermostat Assembly

KiSC issued 08, 2009 A

Содержание G23
























































































































































































































































































































































Результаты поиска

Содержание G23

Отзывы:

Бренды по названию

Популярные бренды

Kubota G23, Руководство по ремонту

Результаты поиска

Содержание G23

Отзывы:

Бренды по названию

Популярные бренды