Kubota G23 Скачать руководство пользователя страница 56 | Manualshive

Страница: 56 / 343

Kubota G23 Скачать руководство пользователя страница 56

GENERAL

G23, G26, WSM

G-38

(EU)

Checking Fuel Lines and Fuel Filter Element

CAUTION

To avoid personal injury :

• Stop the engine and remove the key before checking fuel

lines and fuel filter.

• Check the fuel lines periodically. The fuel lines are subject

to wear and aging. Fuel may leak out onto the running
engine, causing a fire.

The fuel line connections should be checked annually or every

100 service hours, whichever comes first.
1. The fuel lines is made of rubber and ages regardless of service

period.

2. After inspection, if the fuel line and clamps are found damaged

or deteriorated, replace them.

3. Check fuel filter (1), if it is clogged by debris or contaminated

with water, replace it.

IMPORTANT

• When the fuel line is disconnected for maintenance or

repair, close both ends of the fuel line (2) with clean plug of
suitable size to prevent dust and dirt from entering.
Particular care must be taken not to admit dust and dirt into
the fuel system. Entrance of dust and dirt cause
malfunction of the fuel pump.

9Y1210294GEG0041US0

[5] CHECK POINT OF EVERY 150 HOURS

Checking Gear Box Oil

CAUTION

To avoid personal injury :

• Be sure to stop the engine and remove the key before

changing the oil.

• Remove the right and left hand shields from the mower

deck.

1. To drain the used oil, remove the oil level dipstick (1) and the

drain plugs (2) at the gear box, tilt the mower deck and drain the
oil completely into the oil pan.

2. Reinstall the drain plugs (2).
3. Fill with the new oil.
4. After filling reinstall the oil level dipstick (1).

9Y1210294GEG0022US0

(1) Fuel Filter
(2) Fuel Line
(3) Pipe Clamp

(4) Fuel Pump and Filter
(5) Fuel Line
(6) Pipe Clamp

(1) Oil level Dipstick

(2) Drain Plug

KiSC issued 08, 2009 A

«
...
54
55
56
57
58
...
»

Содержание G23
























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды