manualshive.com logo in svg

Kubota G23, Руководство по ремонту

Поделиться
Скачать
Kubota G23 Скачать руководство пользователя страница 312

MOWER

G23, G26, WSM

7-M3

(EU)

3. LIFTING MECHANISM

Mower lift is performed by the mower lift cylinder (1) installed on the machine.
The mower should be kept at 

"UP"

 position when traveling.

When the mower lift lever is set to 

"UP"

 position, the mower lift cylinder (1) is extended by the oil pressure of the

hydraulic system. And the lift link (2) and the front arm (LH) (4) rotates counterclockwise.

The height link (5) and the connect link (6) are pulled.
The rear arm (LH) (7) rotates counterclockwise.
The lift lower link (LH) (8) is lifted up and the mower deck is lifted up.

9Y1210294MOM0003US0

(1) Mower Lift Cylinder
(2) Lift Link

(3) Front Arm
(4) Front Arm (LH)

(5) Height Link
(6) Connect Link

(7) Rear Arm (LH)
(8) Lift Lower Link (LH)

KiSC issued 08, 2009 A

Содержание G23
























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды