manualshive.com logo in svg

Kubota G23, Руководство по ремонту

Поделиться
Скачать
Kubota G23 Скачать руководство пользователя страница 213

FRONT AXLE

G23, G26, WSM

3-S7

(EU)

Separating Front Axle Assembly

1. Disconnect the hydraulic hoses (1), (6) from the power steering

cylinder (2).

2. Remove the split pin (5).
3. Loosen the nut (4).
4. Hook the machine with a nylon sling.
5. Remove the cir-clip (11) and the washer (10).
6. Remove the front tyres.
7. Support the front axle assembly (3) with a garage jack.
8. Remove the nut (4) and the centre shaft (7).
9. Separate the front axle assembly (3) from the machine.

(When reassembling)

• Adjust the front axle rocking force.

9Y1210294FAS0008US0

Front axle rocking force

Factory specification

20 to 300 N
2.0 to 30.6 kgf
4.4 to 67.5 lbf

Tightening torque

Tie-rod end nut

17.7 to 34.3 N·m
1.8 to 3.5 kgf·m
13.1 to 25.3 lbf·ft

(1) Hydraulic Hose
(2) Power Steering Cylinder
(3) Front Axle Assembling
(4) Nut
(5) Split Pin
(6) Hydraulic Hose

(7) Centre Shaft
(8) Front Tyre
(9) King Pin
(10) Washer
(11) Cir-clip
(12) Nylon Sling

KiSC issued 08, 2009 A

Содержание G23
























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды