manualshive.com logo in svg

Kubota G23, Руководство по ремонту

Поделиться
Скачать
Kubota G23 Скачать руководство пользователя страница 125

ENGINE

G23, G26, WSM

1-S43

(EU)

Cylinder Head Flaw

1. Prepare an air spray red check.
2. Clean the surface of the cylinder head with detergent (2).
3. Spray the cylinder head surface with the red permeative liquid

(1). Leave it five to ten minutes after spraying.

4. Wash away the read permeative liquid on the cylinder head

surface with the detergent (2).

5. Spray the cylinder head surface with white developer (3).
6. If flawed, it can be identified as red marks.

9Y1210272ENS0058US0

Valve Recessing

1. Clean the cylinder head surface, valve face and valve seat.
2. Insert the valve into the valve guide.
3. Measure the valve recessing with a depth gauge.
4. If the measurement exceeds the allowable limit, replace the

valve.

5. If it exceeds the allowable limit after replacing the valve, replace

the cylinder head.

[G23]

[G26]

9Y1210294ENS0053US0

(1) Red Permeative Liquid
(2) Detergent

(3) White Developer

Valve recessing

Factory specification

–0.10 (protrusion) to 
0.10 (recessing) mm
–0.0039 (protrusion) to 
0.0039 (recessing) in.

Allowable limit

0.30 (recessing) mm
0.012 (recessing) in.

Valve recessing

Factory specification

0.050 (protrusion) to 
0.25 (recessing) mm
0.0020 (protrusion) to 
0.0098 (recessing) in.

Allowable limit

0.40 (recessing) mm
0.016 (recessing) in.

(1) Cylinder Head Surface

(A) Recessing
(B) Protrusion

KiSC issued 08, 2009 A

Содержание G23
























































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды