KTM 50 SX 2017 Скачать руководство пользователя

Страница: 40 / 104

SERVICE WORK ON THE CHASSIS

V00273-10

–

Remove protective ring



–

Remove the lower triple clamp with the steering stem.

–

Take out the upper steering head bearing.

11.10

Installing the lower triple clamp

601602-10

Main work

–

Clean the bearing and sealing elements, check for damage, and grease.

High viscosity grease (

p. 95)

–

Insert the lower triple clamp with the steering stem. Mount upper steering head
bearing



–

Check whether upper steering head seal



is correctly positioned.

–

Push on protective ring



V00282-10

–

Position the upper triple clamp with the handlebar.

–

Mount nut



, but do not tighten it yet.

H01162-12

(50 SX)

–

Position the fork legs.

Bleeder screws



are positioned toward the front.

Info

The second milled groove in the fork leg must be flush with the upper
edge of the upper triple clamp.

V00274-10

–

Tighten screws



Guideline

Screw, bottom triple clamp

15 Nm
(11.1 lbf ft)

Содержание 50 SX 2017









































































































Результаты поиска

Содержание 50 SX 2017

Отзывы:

Похожие инструкции для 50 SX 2017

Бренды по названию

Популярные бренды

KTM 50 SX 2017, Руководство пользователя

Результаты поиска

Содержание 50 SX 2017

Отзывы:

Похожие инструкции для 50 SX 2017

Бренды по названию

Популярные бренды