KTM 50 SX 2017 Скачать руководство пользователя

Страница: 80 / 104

TUNING THE ENGINE

H01456-01

–

Lay the vehicle down on its left side as shown.

H01458-10

–

Remove screws



–

Remove clutch cover



with the seal ring.

15.10

Adjusting the clutch

Preparatory work

–

Remove the clutch cover.

(

p. 77)

H01459-10

Main work

–

Turn the outer clutch hub



until adjusting screws



become accessible.

H01479-10

Condition

If there is no reference point:

–

Turn adjusting screws



counterclockwise to the last detectable click.

–

Turn adjusting screws



clockwise by 9 clicks to the basic setting.

Guideline

Basic setting of slip speed

8,700… 9,300 rpm

Info

The springs may not be pretensioned by more than 17 clicks from the
stop using the adjusting screws.

Condition

If the slip speed is too low:

–

Turn adjusting screws



clockwise.

Guideline

1 click increases the slip speed by

250… 350 rpm

Info

The springs may not be pretensioned by more than 17 clicks from the
stop using the adjusting screws.

Condition

If the slip speed is too high:

–

Turn adjusting screws



counterclockwise.

Guideline

1 click decreases the slip speed by

250… 350 rpm

Содержание 50 SX 2017









































































































Результаты поиска

Содержание 50 SX 2017

Отзывы:

Похожие инструкции для 50 SX 2017

Бренды по названию

Популярные бренды

KTM 50 SX 2017, Руководство пользователя

Результаты поиска

Содержание 50 SX 2017

Отзывы:

Похожие инструкции для 50 SX 2017

Бренды по названию

Популярные бренды