KTM 50 SX 2017 Скачать руководство пользователя

Страница: 68 / 104

BRAKE SYSTEM

H01450-10

–

Insert the new brake linings.

Info

Always change the brake linings in pairs.
Ensure that the brake linings are correctly positioned in the holding spring.

–

Position the brake caliper on the brake disc.

The brake linings are correctly positioned.

–

Attach the brake line to holder



S00880-10

–

Mount and tighten screws



Guideline

Rear brake caliper screw

10 Nm
(7.4 lbf ft)

Loctite

243™

–

Mount screw



Guideline

Screw, brake linings

8 Nm (5.9 lbf ft)

–

Mount lock washer



–

Check the brake discs. (

p. 57)

H01187-10

–

Operate the foot brake lever repeatedly until the brake linings are in contact with
the brake disc and there is a pressure point.

–

Add brake fluid up to level



Guideline

Level



(brake fluid level below reser-

voir rim)

10 mm (0.39 in)

Brake fluid DOT 4 / DOT 5.1 (

p. 93)

–

Position the membrane and the cover with the washer. Mount and tighten the
screws.

Info

Clean up overflowed or spilled brake fluid immediately with water.

Finishing work

–

Remove the motorcycle from the lift stand. (

p. 34)

Содержание 50 SX 2017









































































































Результаты поиска

Содержание 50 SX 2017

Отзывы:

Похожие инструкции для 50 SX 2017

Бренды по названию

Популярные бренды

KTM 50 SX 2017, Руководство пользователя

Результаты поиска

Содержание 50 SX 2017

Отзывы:

Похожие инструкции для 50 SX 2017

Бренды по названию

Популярные бренды