Kontron TIGW1U Скачать руководство пользователя страница 73

Страница: 73 / 104

Kontron Carrier Grade Server TIGW1U

December 2009

Product Guide, rev. 1.3

Server Utilities—TIGW1U server

7. Reconnect the power and restart the system.

The password and/or CMOS is now cleared and can be reset by going into the BIOS

setup.

4.1.5

BMC Force Update Procedure

When performing a standard BMC firmware update procedure, the update utility places

the BMC into an update mode to allow the firmware to load safely onto the flash device.

In the unlikely event that the BMC firmware update process fails because the BMC is

not in the proper update state, the server board provides a BMC Force Update jumper

that can force the BMC into the proper update state. Use the following procedure if the

standard BMC firmware update process fails.

Once the firmware update process completes successfully, the firmware update utility

may generate an error stating that the BMC is still in update mode. Use the following

procedure to get out of Update mode.

1. Power down and remove AC power.
2. Open the server chassis (remove the top cover).
3. Remove the jumper from J1E3.
4. Close the server.
5. Reconnect the AC power and restart the system.

Now perform the standard BMC firmware update procedure as documented in the

README.TXT file included in the BMC Firmware Update package.

Note:

Normal BMC functionality is disabled when the Force BMC Update jumper is populated.

The server should never be run with the BMC Force Update jumper populated and

should only be used when the standard firmware update process fails. This header

should remain unpopulated by default when the server is running normally.

4.2

Upgrading the BIOS

The upgrade utility allows you to upgrade the BIOS in flash memory. The code and data

in the upgrade file include the following:

• On-board system BIOS, including the recovery code, BIOS Setup Utility, and

strings.

• On-board video BIOS, SCSI BIOS, and other option ROMs for devices embedded on

the server board.

• OEM binary area.
• Microcode.
• A means to change the BIOS language.

4.2.1

Preparing for the Upgrade

The steps below explain how to prepare to upgrade the BIOS, including how to record

the current BIOS settings and how to obtain the upgrade utility.

Note:

In the unlikely event that a BIOS error occurs during the BIOS update process, a

recovery process may need to be followed to return the system to service. See

Section

1.4, “Additional Information and Software” on page 10

for additional information.

Содержание TIGW1U









































































































Результаты поиска

Содержание TIGW1U

Отзывы:

Kontron TIGW1U, Руководство по эксплуатации продукта, Страница: 73 / 104

Результаты поиска

Содержание TIGW1U

Отзывы: