Kontron CP6500-V Скачать руководство пользователя страница 84

Страница: 84 / 192

Configuration

CP6500-V

Page 4 - 4

ID 28945, Rev. 01

P R E L I M I N A R Y

2894

5.01.UG.VC.050304/09095

4.1.4

Shorting Chassis GND (Shield) to Logic GND

The front panel and front panel connectors are isolated to the logic ground.

To enable the connection between the chassis GND and logic GND the capacitors must be
exchanged with zero ohm resistors.

The default setting is indicated by using italic bold.

4.1.5

VGA CRT Rear I/O Configuration

The VGA CRT signals are configurable either for rear I/O or front I/O using the jumper J17.

The default setting is indicated by using italic bold

4.1.6

Front-I and Front-II General Purpose LEDs

The General Purpose LEDs are available for either general application use or indicating the
POST code during boot-up.

When POST code is selected, the General Purpose LEDs indicate POST code during BIOS
boot-up. If not required to indicate POST code, they can be used as general purpose LEDs.

The default setting is indicated by using italic bold.

Table 4-4: Shorting Chassis GND (Shield) to Logic GND

CAPACITOR

SETTING

DESCRIPTION

C1, C3, C4, C5

Closed 470pF 2KV capacitors

Connectors are isolated to logic GND with three
470pF 2KV capacitors

Closed zero ohm resistors

Connectors are connected to logic GND and chassis
GND

C63, C224, C64,

C205

Closed 1.5nF 2KV capacitors

Connectors are isolated to logic GND with four
1.5nF 2KV capacitors

Closed zero ohm resistors

Connectors are connected to logic GND and chassis
GND

Table 4-5: VGA-CRT Jumper Setting

J17

DESCRIPTION

Open

Only front I/O

Closed

Only rear I/O

Table 4-6: General Purpose LED Setting

J18

DESCRIPTION

Open

General purpose functionality

Closed

POST code

Содержание CP6500-V

































































































































































































Результаты поиска

Содержание CP6500-V

Отзывы:

Бренды по названию

Популярные бренды

Kontron CP6500-V, Руководство пользователя

Результаты поиска

Содержание CP6500-V

Отзывы:

Бренды по названию

Популярные бренды