manualshive.com logo in svg

Kontron CP6500-V, Руководство пользователя

Поделиться
Скачать
Kontron CP6500-V Скачать руководство пользователя страница 169

 

 

 

Chapter 6: Security Setup 

 

37 

Security Setup, 

Continued

 

 

Change Supervisor Password  

 

Select this option and press <Enter> to access the sub menu. You can use the sub menu to 
change the supervisor password. 

 

 

Change User Password    

Select this option and press <Enter> to access the sub menu. You can use the sub menu to 
change the user password. 

 

 

Clear User Password  

 

Select this option and press <Enter> to access the sub menu. You can use the sub menu to 
clear the user password. 

 

 

Boot Sector Virus Protection 

This option is near the bottom of the Security Setup screen. The Optimal and Fail-Safe 
default setting is 

Disabled

 

 

Option Description 

Disabled 

Set this value to prevent the Boot Sector Virus Protection. This is the default setting. 

Enabled 

Select Enabled to enable boot sector protection. CP6500-V displays a warning when any 
program (or virus) issues a Disk Format command or attempts to write to the boot sector of the 
hard disk drive. If enabled, the following appears when a write is attempted to the boot sector. 
You may have to type N several times to prevent the boot sector write. 
Boot Sector Write! 
Possible VIRUS: Continue (Y/N)? _ 
The following appears after any attempt to format any cylinder, head, or sector of any hard disk 
drive via the BIOS INT 13 Hard disk drive Service: 
Format!!! 
Possible VIRUS: Continue (Y/N)? _ 

 

 

CHANGE SUPERVISOR PASSWORD 

 

Change Supervisor Password  

Select Change Supervisor Password from the Security Setup menu and press <Enter>. 
 

Enter New Password: 

 
appears. Type the password and press <Enter>. The screen does not display the 
characters entered. Retype the password as prompted and press <Enter>. If the password 
confirmation is incorrect, an error message appears. The password is stored in NVRAM 
after CP6500-V completes. 

 

Cont’d 

Содержание CP6500-V

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды