Kontron CP6500-V Скачать руководство пользователя страница 32

Страница: 32 / 192

Introduction

CP6500-V

Page 1 - 14

ID 28945, Rev. 01

P R E L I M I N A R Y

2894

5.01.UG.VC.050304/09095

HW Monitoring

LEDs

System status:

• TH (green): Overtemperature Status, when remains lit during boot-up, it

indicates a power failure.

• WD (green): Watchdog, when remains lit during boot-up, it indicates a PCI

reset is active.

Fast Ethernet status:

• ACT (green):

network activity

• SPEED (green / orange): network speed

General Purpose LEDs:

• I (green):

General Purpose or POST code

• II (green):

General Purpose or POST code

Watchdog

Software configurable two-stage watchdog with programmable timeout ranging
from 125 msec to 256 sec in 12 steps generates IRQ, NMI, or hardware reset.

Thermal Management

CPU overtemperature protection is provided by:

• CPU shut down via hardware monitor
• Custom-designed heat sinks

System Monitor

Integrated HW monitoring in Winbond Super I/O W83627HF for the supervision
of:

•

Several system power voltages

•

Two fan speed input

•

CPU and system temperature

oftware

Software BIOS

AMI BIOS with 1 MB of Flash memory and having the following features:

•

QuickBo

•

QuietBoot

•

BootBlock

•

LAN boot capability for diskless systems (standard Etherboot / PXE on
demand)

•

Boot from USB devices

•

BIOS boot support for USB keyboards

•

Plug and Play capability

•

BIOS parameters are saved in the EEPROM

•

Board serial number is saved within the EEPROM

•

PC Health Monitoring

•

ACPI

Operating Systems

Operating systems supported:

•

Microsoft Windows 2000

•

Microsoft Windows XP

•

Microsoft Windows XP Embedded

•

Linux

•

VxWorks

Table 1-2: CP6500-V Main Specifications (Continued)

CP6500-V

SPECIFICATIONS

Содержание CP6500-V

































































































































































































Результаты поиска

Содержание CP6500-V

Отзывы:

Бренды по названию

Популярные бренды

Kontron CP6500-V, Руководство пользователя

Результаты поиска

Содержание CP6500-V

Отзывы:

Бренды по названию

Популярные бренды