Kontron CP6500-V Скачать руководство пользователя страница 132

vi  

Preface

 

Delay for PCI Config Cycle..................................................................................................... 45

 

Accept Class Code FF ........................................................................................................... 45

 

Reset from System Master..................................................................................................... 45

 

PCI-to-PCI Bridge Reset ........................................................................................................ 45

 

OEM Feature, Continued ........................................................................................................... 46

 

WATCHDOG .......................................................................................................................... 46

 

IRQ5 Routing.......................................................................................................................... 46

 

Watchdog Mode ..................................................................................................................... 46

 

WD Active Time...................................................................................................................... 46

 

Active for boot......................................................................................................................... 46

 

Chapter 9

 

Exit Menu............................................................................................................ 47

 

Save Changes and Exit.......................................................................................................... 47

 

Exit Menu, Continued................................................................................................................. 48

 

Discard Changes and Exit...................................................................................................... 48

 

Discard Changes.................................................................................................................... 48

 

Load Optimal Defaults............................................................................................................ 48

 

Exit Menu, Continued................................................................................................................. 49

 

Load Fail-Safe Defaults.......................................................................................................... 49

 

Chapter 10

 

Deleting a Password ......................................................................................... 51

 

Erase Old Password .................................................................................................................. 51

 

Chapter 11

 

POST Codes....................................................................................................... 53

 

Bootblock Initialization Code Checkpoints................................................................................. 53

 

Bootblock Recovery Code Checkpoints .................................................................................... 54

 

POST Code Checkpoints........................................................................................................... 55

 

POST Code Checkpoints, Continued ........................................................................................ 56

 

DIM Code Checkpoints .............................................................................................................. 57

 

Index ............................................................................................................................................. 59

 

 

 

Содержание CP6500-V

































































































































































































Отзывы: