manualshive.com logo in svg

Kontron CP6500-V, Руководство пользователя

Поделиться
Скачать
Kontron CP6500-V Скачать руководство пользователя страница 151

 

 

 

Chapter 3: Advanced BIOS Setup 

 

19 

 Advanced BIOS Setup,

 

Continued

 

 

Onboard Floppy Controller 

 

 

This option controls the legacy disk controller. 

Option Description 

Disabled 

Disabled turns off all legacy diskette drives. 

Enabled 

Enables the on-board legacy diskette controller. 

 
 

Serial Port1 Address 

This option specifies the base I/O port address and Interrupt Request address of serial 
port 1. The Optimal setting is 

3F8/IRQ4

. The Fail-Safe default setting is 

3F8/IRQ4. 

 

Option Description 

Disabled 

Set this value to prevent the serial port from accessing any system resources. When this option is 
set to 

Disabled

, the serial port physically becomes unavailable. 

3F8/IRQ4 

Set this value to allow the serial port to use 3F8 as its I/O port address and IRQ 4 for the 
interrupt address. This is the default setting. The majority of serial port 1 or COM1 ports on 
computer systems use IRQ4 and I/O Port 3F8 as the standard setting. The most common serial 
device connected to this port is a mouse. If the system will not use a serial device, it is best to set 
this port to 

Disabled

. 

2F8/IRQ3 

Set this value to allow the serial port to use 2F8 as its I/O port address and IRQ 3 for the 
interrupt address. If the system will not use a serial device, it is best to set this port to 

Disabled

. 

3E8/IRQ4 

Set this value to allow the serial port to use 3E8 as its I/O port address and IRQ 4 for the 
interrupt address. If the system will not use a serial device, it is best to set this port to 

Disabled

. 

2E8/IRQ3 

Set this value to allow the serial port to use 2E8 as its I/O port address and IRQ 3 for the 
interrupt address. If the system will not use a serial device, it is best to set this port to 

Disabled

. 

 

 

Serial Port2 Address 

 

This option specifies the base I/O port address and Interrupt Request address of serial 
port 2. The Optimal setting is 

2F8/IRQ3

. The Fail-Safe setting is 

2F8/IRQ3.

  

 

Option Description 

Disabled 

Set this value to prevent the serial port from accessing any system resources. When this option is 
set to 

Disabled

, the serial port physically becomes unavailable. 

3F8/IRQ4 

Set this value to allow the serial port to use 3F8 as its I/O port address and IRQ 4 for the 
interrupt address. If the system will not use a serial device, it is best to set this port to Disabled. 

2F8/IRQ3 

Set this value to allow the serial port to use 2F8 as its I/O port address and IRQ 3 for the 
interrupt address. This is the default setting. The majority of serial port 2 or COM2 ports on 
computer systems use IRQ3 and I/O Port 2F8 as the standard setting. The most common serial 
device connected to this port is an external modem. If the system will not use an external 
modem, set this port to 

Disabled

.  

 

Note:

   Most internal modems require the use of the second COM port and use 3F8 as its I/O 

port address and IRQ 4 for its interrupt address. This requires that the Serial Port2 Address be 
set to 

Disabled

 or another base I/O port address and Interrupt Request address. 

3E8/IRQ4 

Set this value to allow the serial port to use 3E8 as its I/O port address and IRQ 4 for the 
interrupt address. If the system will not use a serial device, it is best to set this port to Disabled. 

2E8/IRQ3 

Set this value to allow the serial port to use 2E8 as its I/O port address and IRQ 3 for the 
interrupt address. If the system will not use a serial device, it is best to set this port to 

Disabled

. 

 

Cont’d 

 

Содержание CP6500-V

































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды