Kontron CP6500-V Скачать руководство пользователя страница 129

Страница: 129 / 192

Preface

iii

Table of Contents

Limitations of Liability ................................................................................................................ii

Trademarks ...............................................................................................................................ii

Table of Contents......................................................................................................................... iii

Chapter 1

Starting CP6500-V ................................................................................................1

Starting CP6500-V ........................................................................................................................1

CP6500-V Setup Menu .................................................................................................................2

Navigation .....................................................................................................................................2

Navigation, Continued...................................................................................................................4

Chapter 2

Main Setup.............................................................................................................5

System Time/System Date ...........................................................................................................5

Chapter 3

Advanced BIOS Setup..........................................................................................7

Advanced BIOS Setup ..................................................................................................................8

CPU CONFIGURATION SCREEN............................................................................................8

CPU Configuration Settings ......................................................................................................8

Advanced BIOS Setup, Continued................................................................................................9

IDE CONFIGURATION SCREEN .............................................................................................9

IDE Configuration Settings ........................................................................................................9

IDE Configuration ......................................................................................................................9

Advanced BIOS Setup, Continued............................................................................................. 10

Onboard PCI IDE Controller................................................................................................... 10

Primary IDE Master, Primary IDE Slave, Secondary IDE Master, Secondary IDE Slave...... 10

Hard disk drive Write Protect.................................................................................................. 10

IDE Detect Time Out (Seconds)............................................................................................. 10

Advanced BIOS Setup,

Continued............................................................................................. 11

ATA (PI) 80 pin Cable Detection ............................................................................................ 11

Advanced BIOS Setup,

Continued............................................................................................. 12

PRIMARY AND SECONDARY IDE MASTER AND SLAVE SUB MENU .............................. 12

Primary and Secondary IDE Master and Slave Settings ....................................................... 12

Drive Parameters.................................................................................................................... 12

Advanced BIOS Setup,

Continued............................................................................................. 13

Type........................................................................................................................................ 13

LBA/Large Mode..................................................................................................................... 13

Advanced BIOS Setup,

Continued............................................................................................. 14

Block (Multi-Sector Transfer).................................................................................................. 14

PIO Mode ............................................................................................................................... 14

DMA Mode.............................................................................................................................. 14

Advanced BIOS Setup,

Continued............................................................................................. 15

S.M.A.R.T. for Hard disk drives.............................................................................................. 15

32Bit Data Transfer ................................................................................................................ 15

ARMD Emulation Type........................................................................................................... 15

Advanced BIOS Setup,

Continued............................................................................................. 16

FLOPPY CONFIGURATION SCREEN.................................................................................. 16

Floppy Configuration Settings ................................................................................................ 16

Advanced BIOS Setup,

Continued............................................................................................. 17

Floppy Drive A: ....................................................................................................................... 17

Advanced BIOS Setup,

Continued............................................................................................. 18

SUPER IO CONFIGURATION SCREEN............................................................................... 18

SuperIO Configuration Screen ............................................................................................... 18

Advanced BIOS Setup,

Continued............................................................................................. 19

Onboard Floppy Controller ..................................................................................................... 19

Serial Port1 Address .............................................................................................................. 19

Содержание CP6500-V

































































































































































































Результаты поиска

Содержание CP6500-V

Отзывы:

Бренды по названию

Популярные бренды

Kontron CP6500-V, Руководство пользователя

Результаты поиска

Содержание CP6500-V

Отзывы:

Бренды по названию

Популярные бренды