Kohler rada Exact-3 B Скачать руководство пользователя

Страница: 8 / 28

1057614-W2-D

INSTALLATION

Installation must be carried out in accordance with these instructions, and

must be conducted by designated, qualified and competent personnel.

The installation must comply with the “Water Supply (Water Fittings) Regulations

or Scottish Byelaws” or any particular regulations and practices, specified by

the local water company or water undertakers.

Before commencing, make sure that the installation conditions comply with

the information given in section: ‘Specifications’. For Type 3 valves, see also

installation conditions in the TMV3 Requirements Manual.

Care must be taken during installation to prevent any risk of injury or damage.

The shower control should be positioned for easy access during use and

maintenance. All routine maintenance procedures can be conducted with the

shower control body in place (except forstrainer and checkvalve access). For

all models, allow a minimum of 80 mm clearance in front of the temperature

control to enable removal of the serviceable parts during maintenance.

The fitting of isolation valves is required as close as is practicable to the water

supply inlets of the thermostatic mixing valve.

The use of supply-line or zone strainers will reduce the need to remove debris

at each shower control point. The recommended minimum mesh aperture

dimension for such strainers is 0.5 mm.

Inlet pressure tappings which allow measurement of the inlet pressures tp

the mixing valve under running conditions are particularly recommended for

healthcare applications with Type 3 valves.

Pipework must be rigidly supported.

Pipework dead-legs should be kept to a minimum. The mixing water outlet piping

should not exceed 2 meters and the overall length from the hot water circuit to

the discharge point should not exceed 5 metres.

10.

Supply pipework layout should be arranged to minimise the effect of other outlet

usage upon the dynamic pressures at the shower control inlets.

11.

Do not use oil-based, non-setting jointing compounds on inlet or outlet

connections.

12.

To eliminate pipe debris it is essential that supply pipes are thoroughly flushed

through before connection to the shower control.

General

Outlet Position/Reversed Inlets

All Rada Exact-3 B shower controls are supplied with inlet connections configured

hot - left

cold - right

, and

top outlet

as standard. It is essential that inlet supplies

correspond with the red and blue markings on the Thermostatic cartridge.

Содержание rada Exact-3 B





























Результаты поиска

Содержание rada Exact-3 B

Отзывы:

Похожие инструкции для rada Exact-3 B

Бренды по названию

Популярные бренды

Kohler rada Exact-3 B, Руководство по эксплуатации продукта

Результаты поиска

Содержание rada Exact-3 B

Отзывы:

Похожие инструкции для rada Exact-3 B

Бренды по названию

Популярные бренды