Galvin Engineering CliniMix Lead Safe 100.00.71.00 Product Installation Manualline Download | Manualshive

Page: 1 / 18

background image

1

Version 2, 31 July 2020, 1 of 18

Version 2.1, 31

st

July 2020, 1 of 18

Doc. No. 07-06.69

CliniMix

®

Lead Safe™

Hob Mounted Thermostatic

Progressive Basin Mixer - Lever

PRODUCT CODES:

- 100.00.71.00

TABLE OF CONTENTS

WATER SUPPLY CONDITIONS

TROUBLESHOOTING

1.0

INTRODUCTION

The CliniMix

®

Lead

Safe™ Hob

Mounted Thermostatic Progressive Basin Mixer - Lever

is a high-

performance thermostatic mixing valve suitable for a wide range of applications. The valve is designed to
comply with ‘AS4032. Thermostatic Mixing Valves - Materials, Design and Performance Requirements’.
The mixing valve has the following features:

−

Complies with the requirements of AS4032.4

– Thermostatic Mixing Valves.

−

Provides high stability of mixed water temperature even under changing inlet conditions.

−

Ensures rapid shut down of mixed outlet flow in the event of hot or cold water supply failure.

−

Designed for quick and simple in-situ servicing.

−

Suitable for installation into AS3500 compliant systems with hot water temperature as low as 55°Celsius.

−

Fitted with tamper resistant temperature adjustment mechanism.

−

Cool touch, non-conductive design in the hot side of the body, which minimises the risk of burns.

−

Round smooth design to facilitate easy cleaning.

−

Self-draining spout design.

−

Hot water disinfection available without removing tap.

IMPORTANT: All GalvinCare

®

mental health taps are tested in accordance with AS/NZS 3718 and leave

our premises in good working order. Document to be read in conjunction with CliniMix

®

Progressive

Thermostatic Mixing Valve manual.

AS 4032.4 ic. A2

SA lo al

1
2
3
...
»

Summary of Contents for CliniMix Lead Safe 100.00.71.00



















Reviews:

No comments

Related manuals for CliniMix Lead Safe 100.00.71.00

Brand: Easy Drain Pages: 9

Brand: Samson Pages: 56

Brand: MAINLINE Pages: 6

Brand: Naber Pages: 2

Brand: Jacob Delafon Pages: 5

Brand: Opal Pages: 5

Cadet 3 2384.010

Brand: American Standard Pages: 2

Brand: Ancona Pages: 6

Brand: Kohler Pages: 8

INDIVIDUAL ELEMENTS

Brand: VADO Pages: 4

Brand: OLI Pages: 60

Metropol 32511 1 Series

Brand: Hans Grohe Pages: 16

Metris Classic 13413 Series

Brand: Hans Grohe Pages: 16

Pulsify 105 1jet Green 24121 Series

Brand: Hans Grohe Pages: 6

Pulsify E 100 24338 1 Series

Brand: Hans Grohe Pages: 16

Pulsify Showerpipe 260 2jet 24240 Series

Brand: Hans Grohe Pages: 44

Pulsify 105 1jet 24130 Series

Brand: Hans Grohe Pages: 4

freestyle nest bed

Brand: Omlet Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands