Installation:
1.
Screw studded rod (D) into the base of the tap (A).
2.
Place the upper seal (C) into the base plinth (B) then place the base plinth (B) onto the bottom of the tap
(A).
3.
Screw the hot & cold water tail pipes (H & I) into the base of the tap (A) as shown.
4.
Place the mixertap (A), base plinth (B) and upper seal (C), onto the sink/worktop, passing the tail pipes (H
& I) and studded rod (D) through the tap hole.
5.
Pass lower gasket (E) and then metal horseshoe (F) over the studded rod (D) and around the flexible tail
pipes (H & I)
6.
Fasten the fixing nut (G) securely onto the fixing stud (D) to fix the tap (A) into its correct location.
7.
Connect the hot and cold tail pipes (H & I) to the water mains using ½” BSPx15mm compression fittings.
After Installation:
Once you have visually checked the new fittings and connections, ensure that all taps and drains are closed
except the new product which should be
left open
. Turn on (reconnect) the water supplies, check carefully for
leaks around the installation and product function. Once you are sure of no leaks, close the new product and
recheck for leaks, turn on the water heating power.
Clean and dry the product of any marks from installation then cover the product with the bag provided to
protect it until use.
Important Technical Data
Minimum operating pressure:
0.2 bar
Maximum operating pressure:
5.5 bar*
Flow characteristics:
Single flow
Maximum hot water temperature
: 60°C*
Recommended hot water temperature:
46°C
*If these temperatures or pressures are exceeded, even for short periods, damage can result and will void your
warranty.
In these instances, reduce the incoming water temperature and or install a pressure reducing valve. Ensure that
your product is fitted in accordance with Local Water Byelaws or regulations by a qualified installer.
These installation guidelines have been prepared for your direction and you must exercise due care at all times.
We do not accept responsibility for problems that may occur through improper installation. Whilst installing
the product take care not to accidentally loosen any screwed assemblies.
Manufacturers Product Reference:
ACT3023
12/2020
FOR SPARES & TECHNICAL SUPPORT CALL
(+44) 01226 283434
All errors and omissions excepted.
ACT3023 - Dual Handle Monobloc
5 Year Warranty
Terms and Conditions:
In the unlikely event that you should experience
any defect in the materials or workmanship of
your new product within 5 years of purchase, the
purchaser’s sole remedy shall be the replacement
(at the manufacturer’s discretion) of all or any
part of the product that is defective. All working
parts and valves are guaranteed for a period of 5
years from purchase. Decorative surface finishes
and O-rings are guaranteed for 1 year from the
date of purchase provided that our advice
concerning care has been observed and no
scouring agents have been used. This is provided
that the product has been used for normal
domestic purposes only and that the care,
installation, and maintenance instructions have
been observed. The warranty extends to the
original purchaser only.
Marks, scuffs and scratches caused by improper
installation or accidental damage are not covered
by this guarantee. Neither are shade variations or
any damage or defect caused by incorrect
installation or abuse of the fitting.
As we are continuously improving and developing
our range of products, finishes & colours, in the
event of a valid claim, we may not be able to
provide an identical replacement for the defective
product throughout the guarantee period. Where
an identical product is no longer available, we will
supply the nearest equivalent from our then
current product range. In assessing your claim, we
must be given the opportunity to discuss your
claim, review your proof of purchase and or
inspect the product as installed prior to removal.
Any agreed product return must be packaged as
received and complete.
No other warranties, express or implied, are
made, including merchantability or fitness for a
particular purpose. Under no circumstances shall
the manufacturer be liable for any loss or damage
arising from the purchase, use or inability to use
this product, or for any special, indirect, incidental
or consequential damages. No liability is accepted
for consequential damage to other household
fixtures, fittings or furnishings arising from this
claim, even if attached to the product. No
installer, dealer, agent or employee has the
authority to modify the obligations or limitations
of this warranty.
Important Care Instructions for your Product:
To maintain the appearance of this product, ensure that it is regularly cleaned only using a clean, soft damp
cloth. A solution of warm water and a mild liquid detergent may be used where necessary, and then the
fitting rinsed thoroughly and wiped dry. Any other cleaning action or use of common domestic cleaning
products will invalidate your warranty.
If the product has a plastic aerator insert at the end of the spout it should be unscrewed and the plastic internal
insert only removed and cleaned or descaled to maintain flow performance. Do not use descaling solution on
any decorative metal housing, rinse the insert thoroughly before reattaching in the reverse order.
Abrasive cleaners, scouring cleaners and acidic cleaners
must not be used on this product
under any
circumstances. Avoid contact with all solvents (including chlorinated solvents, ketones or acetones as these
may result in surface deterioration or etching). Also avoid contact with any harsh household chemicals such as
oven cleaners, drain cleaners, rust removers, paint strippers and toilet bowl cleaners, bar keepers friend or
Brasso.
Please leave these instructions for your customer.
