Kohler rada Exact-3 B Скачать руководство пользователя

Страница: 20 / 28

1057614-W2-D

Thermostatic Cartridge Removal

Figure 1

Temperature and flow knobs are also available with a short lever.

3 mm A/F Hexago

nal Wrench

Locking Screw

Temperature

Knob

Removal Clip

Hub

Thermostatic

Cartridge Assembly

Head Nut

Inlet Port Seals

Foam Seal (Adhesive

Backed)

Cleaning/Renewal of Parts

The interior surface of the shower control body must be clean before refitting

cartridge. If scale or deposition is present, clean (without Thermostatic, flow and

checkvalve cartridges fitted) using a mild proprietary inhibited scale solvent, e.g.

domestic kettle descalent. After descaling, rinse body thoroughly in clean water

before refitting cartridges.

Note!

The body interior must be cleaned carefully and not damaged in any way.

Do not use any abrasive material.

Cartridges may only be cleaned by flushing through under a jet of clean water

to remove lodged particles.

Do not descale

. Cartridges are not serviceable,

and must not be dismantled.

Cartridges cannot be tested individually, service condition should be assessed

as part of the performance check; refer to

Commissioning Checks

When renewing the Thermostatic cartridge, retain the removal clip and head

nut off the displaced unit and refit.

Examine all accessible seals for signs of deformation or damage, and renew as

necessary, taking care not to damage seal grooves (a Service Pack is available,

containing all seals and strainer screens that may be necessary for renewal

during maintenance or servicing.

10.

Lightly coat all rubber seals with a

silicone-only based lubricant

to assist

reassembling (see lubricants).

Содержание rada Exact-3 B





























Результаты поиска

Содержание rada Exact-3 B

Отзывы:

Похожие инструкции для rada Exact-3 B

Бренды по названию

Популярные бренды

Kohler rada Exact-3 B, Руководство по эксплуатации продукта

Результаты поиска

Содержание rada Exact-3 B

Отзывы:

Похожие инструкции для rada Exact-3 B

Бренды по названию

Популярные бренды