Kohler rada Exact-3 B Скачать руководство пользователя | Manualshive

Страница: 19 / 28

background image

19

1057614-W2-D

Lubricants

Silicone based lubricants must only be used on the rubber seals.
Caution! Oil based or other lubricant types may cause rapid deterioration of seals.

Cleaning

The chrome plated parts should be cleaned using a mild washing up detergent or

soap solution, rinsed and then wiped dry with a soft cloth.
Warning! Many household cleaners contain abrasive and chemical substances, and

should not be used for cleaning plated or plastic fittings.

Do not use descalents on this product.

Part Number

Description

1578.046

Thermostatic Cartridge

Maintenance Procedure - Thermostatic Cartridge

Removal (Refer to Figure 1)

1.

Isolate the supplies to the shower control, and open the flow control to release

pressure and to assist the draining of residual water.

2.

Remove the temperature knob assembly, using the 3 mm A/F hexagonal wrench

(supplied). Do not remove the temperature hub.

3.

With removal clip still in place, unscrew the head nut using a 35 mm A/F wrench.

This will release the body shroud and also begin to draw the Thermostatic

cartridge out of the shower control body.

Warning:

some residual water may be released.

4.

Note which inlet aligns with the hot (marked H and coloured red) lug on cartridge.

5.

Pull the Thermostatic cartridge free of the shower control body.

«
...
17
18
19
20
21
...
»

Содержание rada Exact-3 B





























Отзывы:

Нет отзывов

Похожие инструкции для rada Exact-3 B

Бренд: Helvex Страницы: 2

Universal Roof HKA11-12074

Бренд: Petsafe Страницы: 24

Бренд: iTrainer Страницы: 7

Бренд: Hunter Electronics Страницы: 2

Бренд: Moen Страницы: 6

Linearis Comfort

Бренд: Kessel Страницы: 8

Бренд: Viega Страницы: 18

Бренд: Canadian Timber Collection Страницы: 41

Бренд: Smeg Страницы: 6

Бренд: Bristan Страницы: 13

Бренд: Carron Phoenix Страницы: 2

Бренд: ROGERSELLER Страницы: 4

SMARTFLUSH SF4M

Бренд: SpringWell Страницы: 2

Бренд: Kerbl Страницы: 12

Бренд: Fantini Rubinetti Страницы: 24

Бренд: Fantini Rubinetti Страницы: 84

Бренд: MSD Страницы: 33

Бренд: InSinkErator Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды