Kohler rada Exact-3 B Скачать руководство пользователя страница 5

Страница: 5 / 28

1057614-W2-D

SPECIFICATION

Normal Operating Conditions

are considered as:

inlet dynamic pressures nominally balanced to within 10% of each other during

flow

a differential of approximately 50°C between the hot and cold inlet

temperatures, and with differentials of 15-35°C between the blend setting and

either supply

daily usage of 1-6 hours

installation and usage environment not subject to extremes of temperature,

unauthorised tampering or wilful abuse.

Other Applications

For information on other specific applications or suitability, refer to Kohler Mira Ltd,

or Local Agent.

Disinfection

In applications where system chemical disinfection is practised, chlorine can be

used (calculated chlorine concentration of 50 mg/l (ppm) maximum in water, per one

hour dwell time, at service interval frequency). Such procedures must be conducted

strictly in accordance with the information supplied with the disinfectant and with all

relevant Guidelines/Approved Codes of Practice.

If in any doubt as to the suitability of chemical solutions, refer to Kohler Mira Ltd,

or Local Agent.

Pressures and Flow Rates

Operating Parameters

For Type 3 installations, the supply conditions specified in the TMV3 Requirements

Manual take precedence over the operating parameters which follow.

For optimum performance, dynamic supply pressures should be nominally

equal.

Recommended Minimum Dynamic Supply Pressure:

0.15 bar (0.2 bar

healthcare)

Recommended Maximum Dynamic Supply Pressure: 5 bar.

Recommended Minimum Flow Rate:3 l/min

at mid-blend with equal dynamic

supply pressures.

Recommended Maximum Flow Rate: 35 l/min

at mid-blend (which equates

to maximum pressure loss of 3.0 bar).

Maximum Pressure Loss Ratio*

: should not exceed

10:1

, in favour of either

supply, during flow.

Maximum Static Pressure

10 bar

Recommended maximum flow velocity in pipelines is 2 metres/second.

Содержание rada Exact-3 B





























Результаты поиска

Содержание rada Exact-3 B

Отзывы:

Похожие инструкции для rada Exact-3 B

Бренды по названию

Популярные бренды

Kohler rada Exact-3 B, Руководство по эксплуатации продукта

Результаты поиска

Содержание rada Exact-3 B

Отзывы:

Похожие инструкции для rada Exact-3 B

Бренды по названию

Популярные бренды