KitchenAid KBFA20ER Скачать руководство пользователя страница 29

Страница: 29 / 68

4-7

REMOVING THE WATER FILTER CONNECTOR

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

1.  Unplug refrigerator or disconnect power.
2.  Turn off the water supply to the refrigerator.
3.  Open the refrigerator compartment doors

and remove the items inside to access
the water filter.

Water Filter

4. Pull the refrigerator away from the wall.
5. Disconnect the water line from the fit-

ting.

Dual Water

Valve

Tube Clamp

Water Tube

Water Valve

Access Cover

Water Line

Fitting Retainer

6. Squeeze the sides of the water line fit-

ting retainer and slide the retainer off its
bracket, then slide the fitting off the re-
tainer

Water Line

Fitting Retainer

Fitting Bracket

7. Remove the hex-head screw from the

dual water valve tube clamp, and remove
the clamp from the tube (see the lower
left photo).

8. Pull the end of the water tube from the

quick-disconnect on the dual water valve
(lower left photo).

9. Pull the two lengths of water tubing out of

the guides (see the photo below) on the
rear of the refrigerator.

10. Carefully pull the foam block from the

water tubing cutout.

Water Tubing Guide

Water Tubing

Foam Block

Continued on the next page.

Содержание KBFA20ER





































































Результаты поиска

Содержание KBFA20ER

Отзывы:

Похожие инструкции для KBFA20ER

Бренды по названию

Популярные бренды

KitchenAid KBFA20ER, Техническое образование

Результаты поиска

Содержание KBFA20ER

Отзывы:

Похожие инструкции для KBFA20ER

Бренды по названию

Популярные бренды