manualshive.com logo in svg

KitchenAid KBFA20ER, Техническое образование

Поделиться
Скачать
KitchenAid KBFA20ER Скачать руководство пользователя страница 52

5-4

COMPRESSOR

Refer  to  page  4-21  for  the  procedure  for  ac-
cessing the compressor.
1.  Unplug refrigerator or disconnect power.
2.  Remove the overload relay and motor start 

capacitor from the compressor terminals.

3.  Set the ohmmeter to the R x 1 scale.
4.  

To test the compressor,

 touch the ohm-

meter test leads to the indicated compres-
sor pins. The meter should indicate as fol-
lows:
a) Run (R) to common (C) = 3.3 Ω.
b) Start (S) to common (C) = 4.3 Ω.

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.

R

S

C

Compressor 

Pinouts

Overload 

Relay

Motor Start

Capacitor

Overload Relay & 

Motor Start Cap

5. 

To  test  the  motor  start  capacitor,

  set 

the  ohmmeter  to  the  10K  scale.  Touch 
the  ohmmeter  test  leads  to  the  capaci-
tor terminals. The meter should indicate 
several ohms, and then gradually return 
to infinity.

Содержание KBFA20ER





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды