KitchenAid KBFA20ER Скачать руководство пользователя страница 38

Страница: 38 / 68

4-16

12.

To remove the defrost heater & evapo-
rator:

a) Disconnect the left and right main har-

ness wire connectors from the heater
connectors.

b) Unsnap the heater wire connectors

from the left and right air dams.

f) Pull the bottom of the evaporator

out and rotate it up several inches.

IMPORTANT:

When you rotate the

evaporator, allow the copper tubing to
bend, and not the evaporator tubing
shown below.

Left & Right Main

Harness Connectors

Left & Right Defrost Heater Connectors

Left Air Dam

Right Air Dam

c) Remove the hex-head screws from

the left and right air dams.

Left Air Dam Screw

Right Air Dam Screw

d) Grasp the evaporator tubing at the

right corner, and forcefully jerk the
tubing forward to disengage the tubing
from the plastic standoff (see inset).

e) Repeat the previous step, and disen-

gage the left side of the evaporator
tubing from its plastic standoff.

Evaporator

Standoff

Air Dam

Adhesive

Tape

g) Carefully pull the adhesive foam tape,

on the left and right air dams, (see the
top left photo), off the freezer liner.

h) Continue to rotate the bottom of the

evaporator up until it is high enough
to access the bottom of the defrost
heater, and prop it up.

i) Remove the two heater clips from the

bottom of the evaporator.

j) Pull the defrost heater off the evapora-

tor and remove it.

Copper

Tubing

Do Not Bend This Tubing

Heater Clips

Pull Heater Out

REASSEMBLY NOTE:

Make sure that when

you reinstall the evaporator, the air dam tape
is pressed tightly against the freezer liner. If it
is not properly installed, there will be air leaks
that can cause operational problems.

Содержание KBFA20ER





































































Результаты поиска

Содержание KBFA20ER

Отзывы:

Похожие инструкции для KBFA20ER

Бренды по названию

Популярные бренды

KitchenAid KBFA20ER, Техническое образование

Результаты поиска

Содержание KBFA20ER

Отзывы:

Похожие инструкции для KBFA20ER

Бренды по названию

Популярные бренды