KitchenAid KBFA20ER Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 68

background image

6-1

DIAGNOSTICS & TROUBLESHOOTING

PROGRAMMING MODE: (FOR PROGRAMMING A NEW CONTROL)

NOTE:

The Program Code is located on the Serial Plate on this unit after the word Code.

1.   Open the Fresh Food door and press and hold the Door Alarm Keypad.
2.   Press and hold Freezer Temperature Down Keypad .
3.   Release the Door Alarm Keypad and wait 3 seconds.
4.   The control will display PE to indicate the programming mode.

DIAGNOSTIC TESTS

5. Entry is confirmed by pressing the Freezer Temperature Down Keypad once more.
6. The control will display the current Program Code. This value should be validated with the

Program Code printed on the unit serial plate.

OptimIce

Push for 3 seconds to

reset water filter light

Filter

Reset

Holiday

Mode

Order Replace

Temp

Alarm

Door

Alarm

Max

Cool

Freezer

Refrigerator

NOTE:

If the Program Code is correct, the Programming Mode is exited by closing the Refrigera-

tor door(s).
7. Press the Refrigerator Temperature Up Keypad or Refrigerator Down Keypad to change the

digit value with each key press.

8. The decimal point indicates the selected digit. Press the Freezer Temperature Up Keypad

to select the next digit.

9. Once the desired Program Code is entered, press and hold the Freezer Temperature Down

Keypad until the Program Code begins flashing indicating it has been saved.

NOTE:

If you attempt to enter an invalid Program Code the control will not save the new code,

but will beep. (The unit will NOT run with a Program Code of 0000).Once the Program Code
has been saved, the Programming Mode is exited by closing the Refrigerator door(s). If the new
code is incorrect this process should be repeated after closing the Refrigerator door(s).

The Programming mode can be exited at any time by closing the Refrigerator Door(s) or
will exit if unattended for four minutes.

DEFROST OPERATION

The Control Board adapts the compressor run time between defrosts to achieve optimum de-
frost intervals by monitoring the length of time the defrost heater is on. After initial power up,
defrost interval is 4 hours compressor run time. Defrost occurs immediately after the 4 hours
has elapsed.

PE0

000

OptimIce

Push for 3 seconds to

reset water filter light

Filter

Reset

Holiday

Mode

Order Replace

Temp

Alarm

Door

Alarm

Max

Cool

Freezer

Refrigerator

«
...
51
52
53
54
55
...
»

Содержание KBFA20ER





































































Отзывы:

Нет отзывов

Похожие инструкции для KBFA20ER

Бренд: Haier Страницы: 15

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 30

Бренд: Haier Страницы: 19

Бренд: Haier Страницы: 17

Бренд: Haier Страницы: 14

Бренд: mabe Страницы: 10

Бренд: mabe Страницы: 20

Бренд: Zanussi Страницы: 16

PSHS6TGXSS - Profile 26' Dispenser...

Бренд: GE Страницы: 2

Бренд: Husky Страницы: 6

Бренд: arcelik Страницы: 50

Бренд: Jenn-Air Страницы: 65

Бренд: ZANKER Страницы: 18

FX Series FX2-4N1WS

Бренд: Randell Страницы: 2

Бренд: Magic Chef Страницы: 8

Бренд: mabe Страницы: 37

Бренд: Daewoo Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды