KitchenAid KBFA20ER Скачать руководство пользователя страница 14

Страница: 14 / 68

2-4

NOTE:

The green, ground wire remains

attached to the hinge.

6. Remove the parts for the top hinge, as

shown in Top Hinge graphic, and lift the
left-hand side door from the bottom hinge
pin.

7. Remove the shim from the bottom hinge

pin and keep it for later use (see Bottom
Hinge graphic).

Replace Doors and Hinges

1. Assemble the parts for the top hinge, as

shown in Top Hinge graphic. Do not tight-
en the screws completely.

DOOR REMOVAL AND REPLACEMENT

Top Hinges

A. Hinge Cover Screw

B. Top Hinge Cover

" Hex-Head Hinge Screws

D. Top Hinge

A. Shim

C. Hinge Screws

B. Bottom Hinge

Bottom Hinges

Wire Harness

A
B
C

" Set Screw

2. Replace the parts for the bottom hinge as

shown in Bottom Hinge graphic. Tighten
screws. Replace the refrigerator door.

NOTE:

Provide additional support for the

refrigerator door while the hinges are be-
ing moved. Do not depend on the door
gasket magnets to hold the door in place
while you are working.

3. Align the door so that the bottom of the

refrigerator door aligns evenly with the
top of the freezer drawer, and then tight-
en all of the screws.

4. Reconnect the wire harness on top of the

left-hand side refrigerator door.

5. Replace the top hinge covers.

Содержание KBFA20ER





































































Результаты поиска

Содержание KBFA20ER

Отзывы:

Бренды по названию

Популярные бренды

KitchenAid KBFA20ER, Техническое образование

Результаты поиска

Содержание KBFA20ER

Отзывы:

Бренды по названию

Популярные бренды