KitchenAid KBFA20ER Скачать руководство пользователя страница 24

Страница: 24 / 68

4-2

REMOVING THE REFRIGERATOR THERMISTOR, USER

INTERFACE BOARD, DOOR SWITCH, & LIGHT SOCKET

Electrical Shock Hazard

Disconnect power before servicing.
Replace all parts and panels before
operating.
Failure to do so can result in death or
electrical shock.

1. Unplug refrigerator or disconnect power.
2. Open the refrigerator compartment doors

and remove any items that are below the
user interface.

3. Hook a thumb in the indent of the light

shield, pull back on the shield, and re-
move it from the user interface housing.

Pull Back On

Light Shield

User Interface

4. Place the tip of a flat-bladed screwdriver

into each of the slots in the bottom of the
user interface, (see the photos at the top
right), and twist the screwdriver to release
the locking tabs from the interface. Lower
the interface assembly.

User Interface

Slots

To remove the refrigerator thermistor:

a) Pull the thermistor out of the user in-

terface housing clips.

b) Cut the wires coming from the therm-

istor near the body.

c) Splice the ends of the wires from the

replacement thermistor, to the ends of
the wires you cut from the old thermis-
tor in the previous step.

NOTE:

Trim the

wire lengths, as necessary, so that they
fit neatly into place when the user inter-
face is reinstalled.

Refrigerator

Thermistor

User Interface Assembly

Assembly Shown Removed

Содержание KBFA20ER





































































Результаты поиска

Содержание KBFA20ER

Отзывы:

Похожие инструкции для KBFA20ER

Бренды по названию

Популярные бренды

KitchenAid KBFA20ER, Техническое образование

Результаты поиска

Содержание KBFA20ER

Отзывы:

Похожие инструкции для KBFA20ER

Бренды по названию

Популярные бренды