Kimberly-Clark M1000 Скачать руководство пользователя страница 56

Страница: 56 / 56

At Kimberly-Clark, our mission is

to deliver clinical solutions

that you can depend on

to meet the demands

of your fast-paced world.

Whether your needs involve

preventing healthcare-associated

infections, surgical and digestive

solutions or pain management,

with Kimberly-Clark you’ll

always have one less worry.

Healthcare-Associated
Infection Solutions

Surgical Solutions

Digestive Health

Pain Management

Commitment to Excellence

If, for any reason, our products do not meet your expectations, please let us

know your comments or suggestions for improvement. Your input will result

in a concerted effort on our part to meet your requirements. Our goal is to

provide quality products that completely meet your needs time after time.

For more information, please call your Kimberly-Clark representative or visit our web site at

www.kchealthcare.com.

* Registered Trademark or Trademark of Kimberly-Clark Worldwide, Inc.

14-60-061-0-01

H00242 H0735-07-01

Содержание M1000

























































Результаты поиска

Содержание M1000

Отзывы:

Kimberly-Clark M1000, Руководство оператора, Страница: 56 / 56

Результаты поиска

Содержание M1000

Отзывы: