Kimberly-Clark M1000 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 56

Kimberly-Clark M1000 Скачать руководство пользователя страница 12

K

imberly

-c

larK

* Patient Warming Systems

M000 Control Unit Operator’s Manual: U .S .

The Patient Warming System M000 Control Unit can be operated from remote loca-
tions by attaching the User Interface (Figure 3) to an IV pole or other suitable holder .
The User Interface is connected to the Patient Warming System M000 by a .
metre (42 inch) cable . A 4 .6 metre (5 foot) cable is also available .

Figure 3

Kimberly

Clark

*

There are four principle modes of operation . These can be accessed by
pressing any of the four keys on the lower right side of the display: Automatic,
Manual, Purge, and Stop . Each key represents a unique function of the
KIMBERLY-CLARK* Patient Warming System M000 Control Unit .

a

utOmatic

m

Ode

:

The Automatic Mode monitors and controls the patient’s temperature to a set target
temperature . Water will be cooled or warmed as needed and pulled through the
Thermal Pads to achieve the pre-set patient target temperature . Patient temperature
can be controlled and monitored between 33°C and 37°C (9 .4ºF and 98 .6ºF) .

NOTE: The system will not go into Automatic Mode unless a patient’s temperature
probe is inserted into a patient and attached to the control unit.

CAUTION: The Control Unit will control and monitor core temperature using an

indwelling temperature probe attached to the system. Kimberly-Clark
recommends the use of a second site to verify core temperature while
controlling and monitoring temperature.

m

anual

m

Ode

:

The Manual Mode is functional with or without a patient temperature probe placed .
Water temperature is established and managed by the operator . Patient tempera-
ture is not controlled in Manual mode . The operator must monitor patient tempera-
ture when Manual Mode is active . Water temperature can be modified during the
Manual Mode Operation .

NOTE: Manual Mode can be used prior to placement of a temperature probe or
transition to Automatic Mode.

2 .3 KIMBERLY-CLARK*

Patient Warming

System M000

Control Unit User

Interfaces

2 .4 Modes of

Operation

«
...
10
11
12
13
14
...
»

Содержание M1000

























































Отзывы:

Нет отзывов