Kimberly-Clark M1000 Скачать руководство пользователя страница 36

Страница: 36 / 56

imberly

-c

larK

* Patient Warming Systems

M000 Control Unit Operator’s Manual: U .S .

Tools Needed: 1/8" Hex Wrench

. Unpack both boxes associated with the KIMBERLY-CLARK* Patient Warming

System M000: the Control Unit (Part # 0000-0) and the Installation Kit
(Part # 00839-0) .

2 . Insert the Steel Pole into the moulded base of the cart . Align the depressions in

the pole with the screws in the base of the cart and tighten these screws with
a /8" Hex Wrench . (Figure )

Adjust the top pole such that the hook at the top

points away from the base .

3 . Ensure all four wheels of the cart won’t move by pressing down on the latch

on the wheel . This will aid in attaching the control unit to the cart .

4 . Remove the control unit from the plastic bag and wipe down any

condensation on the exterior of the unit .

5 . Remove the plugs from the Manifold on the back of the unit, and the foam

plug from the vent hole . (Figure 2)

6 . Open the pole clamp on the control unit by turning the handle on the side of

the unit counterclockwise . (Figure 3)

7 Carefully lift the control unit such that the clamp fits just on top of the

support ledge on the pole . Tighten down the pole clamp by turning the pole

clamp handle clockwise until just snug . (Figure 4) Raise top pole and rotate

so curve is extended over control unit .

8 . Remove the fill tube (Part # 00809-02) from its bag and attach it to the fill tube

port located just below the Fluid Delivery Line connection . (Figure 5)

9 . Remove the User Interface Cable [Part # 00832-0(42 in .) or Remote Display

Cable Part # 00832-02 (5 ft .)] from its bag and attach it to the UI Cable Port on

the back of the control unit .

ote

: It is important that the thumbscrews on the connector be tightened

securely to assure a good connection.

(Figures 6 & 7)

0 . Locate a butterfly nut and a cable clamp in the strain relief kit (Part # 00832-99) .

Place the UI Cable in the cable clamp (clamp should be just snug on the cable) .

Leaving approximately 3 in .(7 .5 cm) of cable from the clamp to the connector,

place the clamp on the top metal screw stud located next to the power outlet .

Secure the clamp with the butterfly nut provided .

Appendix A —

Installation & Test

Procedure

Figure 3

Figure 2

Figure 1

Control Unit

Support

Pole Clamp

Handle

Pole Clamp

Fluid Delivery

Line Port

(Manifold)

Содержание M1000

























































Результаты поиска

Содержание M1000

Отзывы:

Kimberly-Clark M1000, Руководство оператора, Страница: 36 / 56

Результаты поиска

Содержание M1000

Отзывы: