Kimberly-Clark M1000 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 56

Kimberly-Clark M1000 Скачать руководство пользователя страница 13

2

K

imberly

-c

larK

* Patient Warming Systems

M000 Control Unit Operator’s Manual: U .S .

The KIMBERLY-CLARK* Patient Warming
System M000 Control Unit control
settings can be adjusted through a
series of menu options displayed
on the LCD screen at the top of the
user interface .

The Menu Control Keys are used to scroll through the various menu options and
adjust settings .

d

Own

Or

u

P

a

rrOw

When in Stop Mode, these keys allow the operator to review custom menu options
and display screens . The arrows are also used for adjusting settings for the custom
options . During Manual Mode, these arrows provide access to the Water Target
Temperature Modification Screen .

e

nter

K

ey

The Enter Key is used to accept modifications or enter changes to a custom
parameter .

h

Ome

K

ey

Pressing the Home Key returns the screen to the Main Menu when in any
custom display screen . This key does not accept modifications or changes .

a

larm

K

ey

The Alarm Key is illuminated when situations arise that may pose a safety issue for
the patient or if the system is not performing to its proper specification . To silence
or acknowledge an alarm or alert, press the Alarm Key .

Kimberly

Clark

*

P

urge

m

Ode

:

The Purge Key removes water from the Thermal Pads . Water flows from the Thermal
Pads back to the reservoir prior to disconnection, which minimizes
leakage and reduces the amount of water remaining in the pads .

NOTE: Pads should be emptied prior to a Fill Cycle. Failure to empty pads before
filling may result in inadequate emptying of the pads, or overfilling the device.

s

tOP

m

Ode

:

The Stop Key halts all modes of operation . During power up and alarm states,
the system defaults to a Stop Mode . While in Stop Mode, all of the customisable
machine settings can be adjusted .

CAUTION: Patient temperature will not be controlled in Stop Mode. Patient

temperature may increase or decrease with the Patient Warming
System M1000 in Stop Mode. Alarms are not enabled in the Stop Mode.

2 .4 Modes of

Operation

(continued)

2 .5 Custom

Menu Keys

«
...
11
12
13
14
15
...
»

Содержание M1000

























































Отзывы:

Нет отзывов