Kimberly-Clark M1000 Скачать руководство пользователя страница 51

Страница: 51 / 56

imberly

-c

larK

* Patient Warming Systems

M000 Control Unit Operator’s Manual: U .S .

Alarm/

Alert

Message
Displayed

Alarm/Alert

Description

System Status

Action

A/D Acquisition
Fault.

Alarm

A/D converter
fault.

Contact Kimberly-Clark Service.

•

Interprocessor
communication
failure (Monitor)

Alarm

The Monitor
Processor does
not communicate.

Contact Kimberly-Clark Service.

•

Interprocessor
communication
failure (Control)

Alarm

The Control
Processor does
not communicate.

Contact Kimberly-Clark Service.

•

Machine Type
Fault.

Alarm

Unit has very little
or no cleaning
solution in the
reservoir.

Turn unit off, drain unit, fill unit using cleaning
kit (part #00838-01). See cleaning kit instructions
for details.
Contact Kimberly-Clark Service.

•

Power Supply
Fault.

Alarm

Power supply volt-
age out of range.

Contact Kimberly-Clark Service.

•

Processor
Fault.

Alarm

Processor Fault.

Contact Kimberly-Clark Service.

•

Unexpected
interrupt.

Alarm

Processor fault.

Contact Kimberly-Clark Service.

•

Processor
Fault.

Alarm

Processor Fault.

Contact Kimberly-Clark Service.

•

Appendix C — Alarm/Alert Table

98.

Содержание M1000

























































Результаты поиска

Содержание M1000

Отзывы:

Kimberly-Clark M1000, Руководство оператора, Страница: 51 / 56

Результаты поиска

Содержание M1000

Отзывы: