manualshive.com logo in svg

Kimberly-Clark M1000, Руководство оператора, Страница: 38 / 56

Поделиться
Скачать
Kimberly-Clark M1000 Скачать руководство пользователя страница 38

37

K

imberly

-c

larK

* Patient Warming Systems 

M000 Control Unit Operator’s Manual: U .S .

5 .   When the machine is full, the pump will stop and the screen will read, “Fill 

Complete .” Press Enter at this point .

6 .   Gently shake and tap the Fill Tube to remove residual water from the line and 

secure the line to the back of the unit using the pre-attached clamps .

7 .   Attach the recirculating line (Part # 00809-04) to the end of the fluid deliver line .
8 .  Press the Manual Key on the User Interface . 
9 .   The target temperature will begin blinking . Using the arrow keys, adjust the 

temperature up or down to 4°C (05 .8ºF) . Press Enter when complete . 

0 .   Allow the machine to run for approximately 5 minutes . Verify that the flow rate 

displayed is at least 3 L/min and that the temperature is climbing . The water 

temperature should reach 4°C (05 .8ºF) within 0 minutes . Some overshoot  

(approximately 0 .5°C) is normal, while the unit will eventually settle at  

the target tempe/- 0 .°C/F .

 .   Change the water temperature set point to 30°C (86ºF) by pressing the Down 

Arrow Key again until the screen reads, “Water Temp Target XX, press Enter to 

change .” Adjust as before, and press Enter when complete .Verify that the  

cooling fan comes on and that the water temperature begins to cool . The unit 

should reach 30°C (86ºF) within 5 to 20 minutes .

2 .   Once the unit has reached 30°C (86ºF), purge the system by pressing the Purge 

Key  . Verify that the water is removed from the recirculating line .

3 .   Turn off the KIMBERLY-CLARK* Patient Warming System M000 Control Unit 

and remove the recirculating line .

4 .   The unit is now ready for use .

Appendix A —

Installation & Test 

Procedure 

(continued)

Figure 11

Figure 13

Figure 10

Figure 9

Figure 12

Latch

Patient

Temp 1 Port

Содержание M1000

























































Отзывы:

Нет отзывов